Question: Should I use 4x4 or 6x6 gate posts?

The standard is 4x4. 6x6 posts make it look more substantial if you do it as a privacy fence. You can use 6x6s if youre doing a good neighbour style fence. ...

What size should a gate post be?

Post size: As a rule of thumb for free-standing posts, use 100mm x 100mm (4″ x 4″) lumber for narrow gates up to 1200mm (4ft) high, use 125mm x 125mm (5″ x 5″) posts for narrow gates 1800mm (6ft) high, and use at least 150mm x 150mm (6″ x 6″) posts for wide gates.

Will a 4x4 support a gate?

4x4 seems to be fairly adequate for standard gates up to 3.5 feet (Meaning a square with a kitty corner cross with fenceboards mounted to it. Depending on the ground layout you can also put a wheel on the gate. If you want enduring fence posts, definitely consider using 2 or 3 inch metal pipe.

What size post do I need for a 12 ft gate?

I would play it as if two gates each being 7 feet or under each, use a 3 inch diameter hinge post. If the gates are to be 10 or 12 feet in with each I would surely use a 4 inch diameter post.

How far apart should 6x6 fence posts be?

On-center spacing (center of post to center of post) may be 4, 6 or 8 depending on the size of the fence panels. Rest the posts on the string, all on the same side. Ensure that the spacing at the corners is never less than 2. Reposition the posts if necessary.

How high should a gate be off the ground?

In most applications, a wood fence should be installed at least two inches off the ground.

How much space should be between gate and post?

For gates with standard 2x4 framing and 4x4 posts, leave a 1/2- to 3/4-inch space between the latch post and the gate frame. On the hinge side, it will depend on the hardware you use. About 1/4 inch is usually sufficient.

How do you stabilize a gate post?

6) If a deteriorated gate post isnt the problem, but your gate still leans, you can straighten it and hold it upright with a turnbuckle and a steel wire or a rod. Simply run it diagonally from the top of the leaning post to the bottom of the second or even third post, down the line.

Is a 12 foot gate wide enough?

Lawn Care Maintenance Equipment and Pedestrian Gates: Typically 3 wide gates are sufficient for push mowers; riding lawnmowers usually require 4-5 wide openings. Most driveway gates are 10 or 12 wide, however some are larger.

What do you put under gate gap?

How Can You Fix A Gap Under A Fence Gate?Wooden Fences. Adding a small wooden step at the bottom of the fence gate will reduce the gap size and also add more stability to the fence. Chain Link. Iron Fences. Plastic Fencing.

How much smaller should gate be than opening?

To build a gate: Measure the opening. You will want to make your gate 1 to 1-1/2 inches smaller than the opening to allow for swing and hardware.

What do you put under a gate?

How Can You Fix A Gap Under A Fence Gate?Wooden Fences. Adding a small wooden step at the bottom of the fence gate will reduce the gap size and also add more stability to the fence. Chain Link. Iron Fences. Plastic Fencing.

Should gates swing in or out?

Your gate should always swing inward. Why? You want the gate to move towards private space, not out to the public. Single gate hinges work on either side.

How deep should a gate post go into the ground?

Sinking the posts into the ground You need to first dig a hole a good 2ft 6 (760mm) to 3ft (915mm) deep (this gets the base of the post below the level that frost penetrates, once below this level the ground is less likely to move as much!

How do you anchor a gate post?

1:045:15How to Set a Secure Gate Post WITHOUT Concrete! - YouTubeYouTube

How wide does a gate need to be for a truck?

Most full size pickup trucks these days are 80-83 inches wide or about 6.5ft wide. 10ft and 12ft gates are typically used if you are going to be driving through the gate with full size trucks or larger vehicles like RVs or trailers.

Is a 10 foot gate wide enough?

The gate needs to be a little wider than your driveway entrance. For example, if your driveway measures up to nine feet, six inches, the ten-foot gate will fit best....Standard sizes.Your Driveway WidthSuggested Gate Size13 10” - 15 9”16 gate3 more rows•Jun 8, 2019

How many bags of concrete does it take to fill a post hole?

Most fence post holes will need between 1 - 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.

Tell us about you

Find us at the office

Smack- Kinneer street no. 65, 62402 Kingston, Jamaica

Give us a ring

Drexel Lepak
+30 694 593 49
Mon - Fri, 7:00-15:00

Contact us