Question: What is a BCC activation fault?

The boiler is operating in hot water mode or the boiler has a call for hot water and the appliance has reached the desired set temperature. BCC (boiler chip card) activation fault.

How do I fix my boiler status 0?

00 or 0, depending on your Logic model, informs you that the boiler is in standby and not receiving a demand from either the hot water or central heating. If you receive this fault code, try running a tap or turning the heating on to see if the status changes.

What does the letter c mean on my boiler?

When C is displayed on your boiler screen it means the boiler has a central heating demand. If the boiler fails to operate then please contact Ideal or alternatively a Gas Safe Registered Engineer if outside of the warranty period.

What does 0 on a boiler mean?

on standby When 0 is displayed on the boiler screen it means the boiler is on standby. This means the boiler is not receiving a demand from either the hot water or central heating.

Why does my boiler say F4?

The F4 fault code tends to signify a problem with your boilers flow thermistor or an issue with its operation. The fault will typically be related to circulation issues. This fault will require a call out to a Gas Safe registered engineer.

What does F4 mean on gas boiler?

If your Glow-Worm boiler is showing the F4 fault code on the display panel, it means there is an ignition fault. Its the printed circuit board (PCB) on your boiler that controls electrical components.

Why does boiler say F1?

The F1 error code tells you that your boiler is losing pressure and is now low on pressure. This may be caused by: Water leaking from the pipes. A leak in the the boiler itself.

What does F and L mean on a boiler?

Boiler is not working for central heating or hot water but attempts to fire by going through 3 ignition attempts. Display shows L : F (flashing). – If no gas supply then not a boiler fault – contact gas supplier.

What does F1 mean on a boiler?

The F1 error code tells you that your boiler is losing pressure and is now low on pressure. This may be caused by: Water leaking from the pipes. Water leaking your radiators. A leak in the the boiler itself.

How do I fix the F1 code on my boiler?

How to Fix the Ideal F1 Error CodeTurning the boiler off.Waiting for the system to cool down.Repressurising the system to 1.0 bar.Bleeding the radiators.

What do I do if my boiler shows F1?

0:013:43Ideal Logic F1 Fault How To Repair your combi boiler - YouTubeYouTube

Is it normal for boiler to lose pressure?

A boiler that keeps losing pressure is therefore always cause for concern. There are two main problems that typically cause a loss of pressure - water escaping somewhere in the system or a failure of the expansion valve and resulting damage to the pressure relief valve.

What do I do if my boiler pressure keeps dropping?

Top tip!Switch off and allow your boiler to cool.Double-check that both ends of the filling loop are securely attached.Open both valves, to allow cold mains water into the system (you should hear it)Wait for the pressure gauge to read 1.5 bar.Close both valves, one after the other.

Why does my Glow-worm boiler keep losing pressure?

A boiler that keeps losing pressure is therefore always cause for concern. There are two main problems that typically cause a loss of pressure - water escaping somewhere in the system or a failure of the expansion valve and resulting damage to the pressure relief valve.

What does E8 mean on a boiler?

Remeha Fault CodesFault CodeRepairDescriptionE6LinkUnwanted flame formationE7LinkNo water in the boiler or the pump is not workingE8LinkFan faultE10LinkNo through flow during venting cycle12 more rows

Tell us about you

Find us at the office

Smack- Kinneer street no. 65, 62402 Kingston, Jamaica

Give us a ring

Drexel Lepak
+30 694 593 49
Mon - Fri, 7:00-15:00

Contact us